Carrier Owners Manual - Enlarge page 1 of 50
2 of 50
3 of 50
4 of 50
5 of 50
6 of 50
7 of 50
8 of 50
9 of 50
10 of 50
11 of 50
12 of 50
13 of 50
14 of 50
15 of 50
16 of 50
17 of 50
18 of 50
19 of 50
20 of 50
21 of 50
22 of 50
23 of 50
24 of 50
25 of 50
26 of 50
27 of 50
28 of 50
29 of 50
30 of 50
31 of 50
32 of 50
33 of 50
34 of 50
35 of 50
36 of 50
37 of 50
38 of 50
39 of 50
40 of 50
41 of 50
42 of 50
43 of 50
44 of 50
45 of 50
46 of 50
47 of 50
48 of 50
49 of 50
50 of 50
From inside (document excerpt):
58UVB Direct Vent Upflow Variable Capacity Condensing Gas Furnace For Sizes 060 120, Series 100 Installation, Start Up, and Operating Instructions NOTE: Read the entire instruction manual before starting the installation. AIRFLOW TABLE OF CONTENTS PAGE SAFETY CONSIDERATIONS 2 DIMENSIONAL DRAWING 3 Clearances to Combustibles 4 CODES AND STANDARDS 5 ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS 6 INTRODUCTION 6 APPLICATIONS .
Heating, Ventilating and Air Conditioning User Manual Free Download. HAVC Operator’s Manual. Gas Furnace and AC Free Instruction Manual Download PDF.
6 General 6 Applications . 6 LOCATION . 8 General 8 Low-Heat Only Installation 10 Location Relative to Cooling Equipment 10 Hazardous Locations . 10 INSTALLATION 10 Leveling Legs (If Desired) . 10 Air Ducts . 11 Filter Arrangement . 11 Bottom Closure Panel . 12 Gas Piping . 12 Electrical Connections 14 Removal of Existing Furnaces from Common Vent Systems 17 Combustion- and Vent Pipe Systems . 18 -air Condensate Drain 32 START-UP, ADJUSTMENTS, AND SAFETY CHECK. 33 General 33 As an ENERGY STAR® Partner, Carrier Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. REGISTERED UPFLOW Fig. 1 Furnace Orientation A06340 ama ISO 9001:2000 CERTIFIED Select Setup Switch Positions . 33 Prime Condensate Trap with Water . 34 Purge Gas Lines . 35 Sequence of Operation 35 Adjustments 43 Check Safety Controls 48 CHECKLIST . 49 SAFETY CONSIDERATIONS ! CAUTION injury or product and property damage. NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or operation. FURNACE RELIABILITY HAZARD Improper installation or misapplication of furnace may require excessive servicing or cause premature component failure. Application of this furnace should be indoors with special attention given to vent sizing and material combustion air requirements, gas input rate, air temperature rise, unit leveling, and unit sizing. ! CUT HAZARD CAUTION Failure to follow this caution may result in personal injury. Sheet metal parts may have sharp edges or burrs. Use care and wear appropriate protective clothing and gloves when handling parts. The 58UVB Condensing Gas-Fired Furnaces are CSA (formerly AGA and CGA) design-certified for natural and propane gases (see furnace rating plate) and for installation in alcoves, attics, basements, closets, utility rooms, crawlspaces, and garages. The furnace is factory-shipped for use with natural gas. A CSA listed gas conversion kit is required to convert furnace for use with propane gas. See Fig. 3 for required clearances to combustibles. Maintain a 1-in. clearance from combustible materials to supply air ductwork for a distance of 36 inches horizontally from the furnace. See NFPA 90B or local code for further requirements. These furnaces SHALL NOT be installed directly on carpeting, tile, or any other combustible material other than wood flooring. These furnaces are suitable for installation in a structure built on site or a manufactured building completed at final site. The design of this furnace line is NOT CSA design-certified for installation in recreation vehicles, manufactured (mobile) homes or outdoors. This furnace is designed for continuous return-air minimum temperature of 60_F db or intermittent operation down to 55_F db such as when used with a night setback thermostat. Return-air temperature must not exceed 80_F db.