Carrier Owners Manual - 1 of 12
Carrier Owners Manual - 2 of 12
Carrier Owners Manual - 3 of 12
Carrier Owners Manual - 4 of 12
Carrier Owners Manual - 5 of 12
Carrier Owners Manual - 6 of 12
Carrier Owners Manual - 7 of 12
Carrier Owners Manual - 8 of 12
Carrier Owners Manual - 9 of 12
Carrier Owners Manual - 10 of 12
From inside (document excerpt):
58CLR Low-Boy Oil Furnace Visit www.carrier.com Installation, Start-Up, and Operating Instructions For Input Capacities of 70,000–154,000; Series 100 NOTE: Read the entire instruction manual before starting the installation. TABLE OF CONTENTS SAFETY CONSIDERATIONS .1 INTRODUCTION 2 LOCATION 3 General 3 Location Relative to Cooling Equipment 3 INSTALLATION .3 Air for Combustion and Ventilation 3 General 3 Duct Work Recommendations 5 Venting 5 Factory-Built Chimneys 5 Oil Burner .5 Oil Connections 6 Barometric Draft Control 6 Electrical Connections 6 Filters .6 STARTUP, ADJUSTMENT, AND SAFETY CHECKOUT .7 Operational Checkout .9 Combustion Check 9 Fan Adjustment Check .10 Limit Control Check .10 For Year-Round Air Conditioning .10 Heating 10 Cooling 10 Constant Blower Switch .10 CARE AND MAINTENANCE .10 General 10 Oil Burner .11 Heat Exchanger and Flue Pipe .11 Blower Removal .11 SAFETY CONSIDERATIONS FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
DO NOT ATTEMPT TO START THE BURNER WHEN EXCESS OIL HAS ACCUMULATED, WHEN THE FURNACE IS FULL OF VAPOR, OR WHEN THE COMBUSTION CHAMBER IS VERY HOT. A96280 Fig. 1–58CLR Low-Boy Oil Furnace Never burn garbage or paper in the heating system and never leave rags, paper, or any flammable items around the unit. These instructions are intended to be used by qualified personnel who have been trained in installing this type of furnace. Installation of this furnace by an unqualified person may lead to equipment damage and/or a hazardous condition which may lead to bodily harm. All local and national code requirements governing installation of oil burning equipment, wiring, and flue connections must be followed. Some of the codes (issued by the Canadian Standards Association, the National Fire Protection Agency, and/or the American National Standards Institute) that may be applicable are: ANSI/NFPA 31: INSTALLATION OF OIL BURNING EQUIPMENT ANSI/NFPA 211: CHIMNEYS, FIREPLACES, VENTS, AND SOLID FUEL BURNING APPLIANCES ANSI/NFPA 90B: WARM AIR HEATING AND AIR CONDITIONING SYSTEMS For use with grade 1 or 2 Fuel Oil. Do not use Gasoline, Crankcase Oil, or any Oil containing Gasoline! Failure to follow this warning could lead to sooting, fire, explosion, and/or severe bodily harm. ANSI/NFPA 70: NATIONAL ELECTRIC CODE CSA B139: INSTALLATION CODE FOR OIL BURNING EQUIPMENT CAS C22.1: CANADIAN ELECTRICAL CODE Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. Book 1 4 PC 101 Catalog No. 535-80011 Printed in U.S.A. Form 58CLR-1SI Pg 1 12-00 Replaces: NEW Tab 6a 8a 21 1/4 20 ” 20 ” 20 ” VENT CONN 10 ” 3 ” D E B C A A98009 Dimensions (In.) UNIT SIZE 10512 12020 UNIT DIMENSIONS Depth Height Width A B 211/4 53-3/4 31-1/2 211/4 60-5/32 34-3/4 FLUE HEIGHT C 26-1/2 28-11/32 RETURN OPENING D 20 22 SUPPLY OPENING E 20 24 VENT CONNECTION 5 6 Fig. 2–Dimensional Drawing Only the latest issues of these codes should be used, and are available from either The National Fire Protection Agency, Batterymarch Park, Quincy, MA 02269 or The Canadian Standards Association, 178 Rexdale Blvd., Rexdale, Ontario M9W 1R3 Recognize safety information.